®™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow
I N S T A L L A T I O N I N F O R M A T I O N . C O M M E R C I A L
blowing agent. Do not breathe
vapor or mist. Use in well-
ventilated areas or wear proper
respiratory protection. Isocyanate
is irritating to the eyes, skin and
respiratory system, and may cause
sensitization by inhalation or skin
contact.
• INSTA STIK
™
Quik Set is very sticky
and will adhere to most surfaces
and skin. Do not get foam on skin.
Wear gloves, and goggles or safety
glasses. Cured foam must be
mechanically removed or allowed
to wear off in time.
• The contents are under pressure.
SURFACE PREPARATION
All surfaces must be free of any
debris, dirt, dust, grease, oil, diesel
fuel and standing water before
INSTA STIK
™
Quik Set is applied.
RE-COVER OVER (BUR)
A certified INSTA STIK
™
Quik Set
instructor, authorized to perform
adhesion tests, must be on site prior
to the commencement of the project
to determine compatibility. Contact
Dow at 1-866-583-BLUE (2583) at
least 14 days in advance for further
instructions.
STEEL DECK
On new steel, the residual shop
oil coating must be removed using
TSP, acetone, naphtha or
comparable cleanser.
INSULATION
Polyisocyanurate insulation boards
cannot exceed 4' x 4' (1.2 m x 1.2 m).
All other boards may be installed up
to a 4' x 8' (1.2 m x 2.4 m) size. In
multiple layers of insulation, the
staggered joint method should be
used to eliminate thermal breaks.
PRODUCT AND EQUIPMENT
INSTALLATION
The INSTA STIK
™
Quik Set Complete
Kit includes a steel tank, a 4' (1.2 m)
flexible dispensing hose, two PVC
dispensing wands, a 1/4" (6.4 mm)
coupler and 9/16" (14 mm) wrench.
The tank can also be purchased
separately.
INSTA STIK
™
Quik Set Commercial
Roofing Adhesive should be shaken
prior to use. Firmly hold the
container on its side and agitate the
contents using a side-to-side motion
for at least 15 seconds. Attach the
swivel hose fitting on the end of the
dispensing hose to the threaded port
of the cylinder valve. Once it is
seated properly, tighten securely
using an open-end wrench
(supplied). Verify that the on/off valve
is attached to the dispensing hose
and is in the off position.
Attach either end of the threaded
wand to the dispensing hose on/off
valve. Tighten securely. Attach the
coupler to the exposed end of the
wand. Attach the second plastic
wand to the coupler. Tighten
securely.
Slowly open the valve at the top of
the cylinder 1/2 to 1 revolution. Open
further if higher velocity is desired.
Check for leaks. If there are no leaks,
INSTA STIK
™
Quik Set is ready for use.
Installation Procedures for
INSTA STIK
™
Quik Set Commercial
Roofing Adhesive
INSTA STIK
™
Quik Set Commercial
Roofing Adhesive is a single-
component polyurethane adhesive.
It is dispensed from a portable
disposable pre-pressurized container
requiring no external power source.
INSTA STIK
™
Quik Set is available in
a 30 lb (13.6 kg) unit (23 lb [10.4 kg]
net chemical weight).
INSTA STIK
™
Quik Set is used to
attach compatible insulation and
coverboards to roof decks and
substrates in new roof and roof
replacement applications, including
insulation board to insulation board,
insulation board to Class I graveled
and non-graveled (bald) built-up
roofs for re-cover applications, and
insulation or gypsum board to 22
gauge and thicker steel decks and
wood decks.
For a faster, labor-saving
application in a correct and
repeatable pattern, the Multi-Bead
Applicator from Dow holds three
tanks of INSTA STIK
™
Quik Set and
allows application of up to eight
beads of adhesive.
GENERAL INFORMATION
The ideal chemical temperature at
the time of application should be
75°F (24°C). The minimum ambient
and surface temperatures must be
33°F (1°C) and rising. INSTA STIK
™
Quik Set is packaged in a single
container that should be stored
between 50°F and 75°F (10°C and
24°C). The shelf life is 15 months
from the date of manufacture.
SAFETY AND CONDITIONS
OF USE
• Read the label and Material Safety
Data Sheet carefully before use.
• INSTA STIK
™
Quik Set Commercial
Roofing Adhesive contains
isocyanate and a hydrofluorocarbon
(24 Seiten)
(4 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern